Quick Answer: Can I Put A 60w Bulb In A 40w Lamp?

What is LED equivalent to 60w?

For a 60-Watt fixture, you could use a 100W, 125W, or even 150W LED equivalent because they all consume under 60-Watts.

The 150W LED equivalent produces about 2,600 lumens, while using only about 30 Watts..

What happens if you put a lower wattage bulb?

If you will use a lower wattage bulb in your fixture you will have less light than before, choosing a lower wattage bulb is fine as long you understand that you are compromising on light output (this statement is correct only for incandescent and halogen bulbs).

Does it matter how many watts a light bulb is?

As long as you don’t put a bulb that uses more than 60 watts in that socket you will be fine. The good news is the energy-saving bulbs that replace a 60-watt incandescent will only use 10 to 15 watts, depending on the actual bulb you buy, and give off the same amount of light.

What is the maximum wattage for a ceiling light?

For a ‘rule of thumb’, overhead lighting probably should not exceed 100 watts (again, check the fixture ratings!), which will provide pretty bright lighting, and should be ample for most uses.

Can you use a 100 watt bulb in a 150 watt lamp?

“100 Watt” written on the fixture means that the fixture is safe (does not set fire or gets too hot) when you use a 100 Watt bulb in it. … These bulbs consume less than 30 Watt however give the output of a 150 Watt traditional bulb. You can safely use such a bulb in your fixture.

Can I put a 60w LED bulb in a 40w lamp?

Yes, assuming you’re suggesting an LED that has lumen output similar to a 60 watt lamp. You can use any lamp that consumes up to 40 watts and is shaped similar to the lamp recommended. So for example, if it was a standard A lamp, you could use any LED lamp that consumes up to 40 watts with no safety issue.

Can you put a 60w bulb in a 100w lamp?

But the wires used to construct the fixture may only be rated to a certain wattage. If a bulb draws 500 watts, and the wires are rated to 100 watts – you’re gonna have a fire. As Engineer said, 60w bulbs in a socket rated at 100 will be fine, as long as voltage is the same.

What happens if you put a 60w bulb in a 40w socket?

Power rating are typical based on what the item can stand/allow. Putting a 60W bulb in a 40W socket, probably won’t cause a problem, but you won’t get better brightness.

Can I use a 42 watt bulb in a 40 watt lamp?

It is ‘safety margin’ and Liability of the jurisdiction delivering the highway to the public. So, would a ’42 Watt Halogen Bulb’ be approved for hookup to a light fixture, when it was certified and approved for operation at 40 Watts.

Is it OK to use a 75 watt bulb in a 60 watt lamp?

If your fixture is rated to accept 60 Watts, you can safely use 75W, 100W, or even 125W equal bulbs (which all draw less than 50 Watts of power) instead.

What is the equivalent of a 40 watt bulb in LED?

Compare wattageTraditional bulb1Halogen2LED40 watts25 watts5 watts60 watts40 watts7 watts75 watts45 watts9 watts100 watts60 watts12 watts1 more row

What happens if you put a higher watt bulb in a lamp?

Using a light bulb with too high of wattage can lead to overheating of the light bulb. This heat can melt the light socket as well as the insulation of the wires. Once that happens, you put yourself at risk of arc faults, and this is something that could even lead to property fires.

Can you put a 40w bulb in a 25w lamp?

With a 40 watt incandescent, then 36 watts would be dissipated in the same surface cylinder (about 12 inches by 6 inches or 72 sq inches of space. This would make the lamps temperature go from the moderate 80–90F to a hazardous 150 to 180. … So NO, do not replace the lamp with a 40W bulb….